Recetear Yaesu FRG-8800

Recetear Yaesu FRG-8800

Notapor golin21 » 02 Jul 2010, 10:43

Hola, tengo un receptor Yaesu FRG-8800, creo que esta bloqueado, me pueden decir como se recetea?, y como conseguir el manual en Español. Gracias un saludo
golin21
 
Mensajes: 3
Registrado: 02 Jul 2010, 10:30

Re: Recetear Yaesu FRG-8800

Notapor elcaja » 03 Jul 2010, 09:50

¿Es la avería que el display se pone en 10.000 y parpadea?
elcaja
Aficionado
Aficionado
 
Mensajes: 198
Registrado: 28 Ene 2008, 00:08

Re: Recetear Yaesu FRG-8800

Notapor ICOSMOS » 03 Jul 2010, 18:31

Hola:

Hazme una descripcion de la averia para hacerme una idea de lo que puede tener averiado.

Saludos
¡¡La inspiracion siempre me pilla trabajando!!
< Tektronix - Marconi/IFR/Aeroflex - EIP - Racal - R&S - HP - Fluke >
ICOSMOS
Recien Llegado
Recien Llegado
 
Mensajes: 40
Registrado: 26 Abr 2009, 20:18
Ubicación: Varias

Re: Recetear Yaesu FRG-8800

Notapor golin21 » 05 Jul 2010, 10:42

Hola, al conectar el equipo se enciende el diplay con una numeración, al girar el Dial a derecha o izquierda no se mueve la numeración, antes de ayer al conectarlo, se encendió el dial como siempre con una numeración y al girar el dial empezó a funcional hacia arriba a y hacia abajo, probamos en 24890, y funcionaba perfectamente, nos pasamos a 28350 y igual, me recibía perfectamente, pero de repente se volvió a bloquear, volvió a enganchar y baje hasta 18888 y se volvió a quedar bloqueado y no hay forma de que vuelva a funcionar como antes, espero su respuesta. Gracias un saludo
golin21
 
Mensajes: 3
Registrado: 02 Jul 2010, 10:30

Re: Recetear Yaesu FRG-8800

Notapor elcaja » 05 Jul 2010, 13:45

Mira a ver si te vale esto


Hi all I trying too repair a FRG-8800 ! 1st no display but suring the net found the fix with reseting the cpu and rmeoving the batts, however it just flashes display at 10.000Mhz the VFO does track and I get the signal strength display at full tilt and no audio, Read that this may be a PLL fault ? but measuring the voltage a TP03 and 10.000Mhz and going upto 29.999Mhz does not seem to ty in with what is on the net. Does anyone have the correct procedure from the Service manual for setting up the PLL, or has anyone seen this fault.

73 de Mark G0LGJ

Hello Scott and others,

Your problem is well known with the FRG-8800. Even my set has had that problem.

>This is what a Yaesu Technical Bulletin gives to fix this problem:
>PROBLEM: The PLL is unlocked when the temperature changes.

>1. Remove the AC cable from the AC jack. Remove the top cover.
>2. Remove the PLL unit from the chassis.
>3. Remove R18 22k ohm 1/4w resistor. Replace with 4.7k ohm 1/4w resistor.
>(add solder side)
>4. Replace the PLL unit.
>5. Replace top cover. Modification is now complete.

But that does not fix the problem always, every set is reacting different!

A better way to handle is find out the right value of the resistor yourself.
First: take the batteries out the compartment.
Connect a resistor of 4K7 in serie with a var. resistor of 47K ohm(or higher).
Remove R18 (near Q05) and connect on the same place your resistors(with some wirering).
1. Turn the var. resistor of 47 K to its max value, power on the set and turn the var. resistor to its minimum value untill the pll locks. Switch power off and on again to see if the pll keeps locking; find the value on witch the pll immideatly locks,
(the display shows 10.000 Mhz).
Remove one end of the resistors and measure with your multi-meter the resistance of the var. resistor; write this value(one)down (say 18K6).
2. Do the same as 1. with the var. resistor turned from its minimum value to its maximum value untill the pll locks; write this value(2) down (say 3K5).
3. The resistor value to replace R18 is:
(value(1) + value(2) + 4K7) devided by two (rounded to the nearest value)
so: (18K6 + 3K5 + 4K7) / 2 = 13K4 (rounded to 12K)

Do you have the service manual to find the right spot of R18? If not, sent a message back to this forum and i will sent it to you.

73's
Theo.
elcaja
Aficionado
Aficionado
 
Mensajes: 198
Registrado: 28 Ene 2008, 00:08


Volver a Yaesu

¿Quién está conectado?

Usuarios registrados: Google [Bot]